Navigation Lights

[commanderpete]

A question came up on another thread about fixing navigation lights.

There could be a number of reasons why the the light doesn't work. The source of the problem is often corroded terminal ends or the socket.

You can try cutting back the wire a bit and making fresh connections, but its probably better just to run new wire.

The socket can be replaced with a standard brass "double contact bayonet socket". Often the old brass socket will have fused into the bronze housing, making removal difficult. If it really won't come out, you can punch the bottom out of the old socket and shove a plastic double contact bayonet socket in there. Its a little smaller than the brass one.

That's about all I know.

[Jim Rester]

On old Commander 80 there is a fishing float sticking out of a hole in the cabin just forward of the cockpit to Starboard. In a corresponding hole on Port there is a nifty little red light.

I am going to go out on a limb here and guess that berfore I'm done I'll need a nifty little green light.

We are trying to do stay as close to original as possible. Does anyone have a source?

Thanks ~ Jim

[Bill]

Jim,

Original hardware for Ariels, Commanders, Triton's and etc., is no longer available. We do have a lead on the original patterns and a navel architecture school that may get possession. (Search on "Ronstand" for more info.) But, this is turning out to be like going through probate . . .

Meanwhile, you can try finding an early Pearson that is headed for the chainsaws and bid on the light fixtures. BTW - I'm looking for an original stern light, in case you find one

[Tony G]

Is this the 'stuff' you guys are refering to?

[Bill]

Yes, that's the original Pearson hardware.

[Tony G]

Make me an offer. I can't refuse.

[Bill]

Do you have the lower half of the stern light? (I'm ok on the running lights.)

[JurisG]

This is probably slightly off-topic, but since this discussion is sticky and it's an obscure part search I'm going to fire away. I am missing this part for my Ariel (see pic). It has a female threaded hole (with an insane thread that is not recognizably metric or standard) and an eye hook on the end of it. Does anyone know what this part is called and/or where I can get a replacement? Even if the thread doesn't match, I will just put a die on the male end of the railing cable and re-cut it. Thanks!

Attachment 6718

[Bill]

This is probably slightly off-topic, but since this discussion is sticky and it's an obscure part search I'm going to fire away. I am missing this part for my Ariel (see pic). It has a female threaded hole (with an insane thread that is not recognizably metric or standard) and an eye hook on the end of it. Does anyone know what this part is called and/or where I can get a replacement? Even if the thread doesn't match, I will just put a die on the male end of the railing cable and re-cut it. Thanks! Attachment 6718

Stop by your local rig shop and take a look at the life line hardware . . . or check a marine store. That appears to be a "gate eye" and there should be a pelican hook on a section of life line that attaches to it.

[mbd]

The bronze stern light cover pictured above that Jerry so graciously offered is available again. It doesn't quite fit MY original glass dome, but you may be able to rework it or find another glass dome to fit. I guess I just need to work on my original stern light to get down to the purty bronze... Thanks Jerry!

[Commander 147]

Mike

How interesting. With my stern light which I believe to be original it was totally interchangeable as was the new glass dome I bought from the same company. These boats really were one off boats with each one unique in some way to all of the others. No computerized tight tolerances like you see in todays production boats.

[Sprite]

I just wanted to start a thread on this item because I found
a person who does exact copies of the Navigation Lights
that you see in the Rostand Catalog in the manual. You know the side lights
and that winged stern light. I found out that they are based on
Herreshoff (sorry about the spelling) templates. This does not surprise
me because Pearson was based out of Bristol, Rhode Island. They
took over the old Herreshoff site in Bristol. They are made of Bronze
and have a special coating so they never deteriorate or patina. I found
this guy in a Wooden Boat magazine he is based out of Hull, Massachusetts.
If anyone is interested add to this thread and I'll post the information on this
thread.

[Bill]

Might be a good idea to have the contact information. Someone could measure the originals on our boats and then check to see if the ones being offered were similar in size.

[mbd]

Does he do other hardware too?

[Sprite]

Yes pulley systems that look like older systems but made with modern alloys.
He has a catalog. His name I think is Jim Reinbeck and he will send out a catalog. He did some historical fittings for a Herreshoff named Joyner. I think
he has made his reputation on historical replicas. But if you see the lights on
this they are mind blowing they look exact. Especially the wings. I have my originals. I am also going to put in LEDs in those bayonet sockets I got info on that too. Less amprage is that right spelling and No replacements. Gotta love it especially when electricity is at a premium.


John