Results 1 to 15 of 90

Thread: STRONGBACK DISCUSSION etc.

Threaded View

  1. #13
    Join Date
    Sep 2001
    Location
    San Rafael, CA
    Posts
    3,621

    Resorcinol vs Epoxy / apples and oranges

    Well,
    Resorcinol is a wood specific 'bonder'.
    If you were gluing exterior mahogany rails up from strips and scarf joints there is no other glue. When you glue coaming blocks and winch islands up with epoxy you will have separation at some point. And as I just said if you have an epoxy glue-up like a bowsprit and/or teak anchor roller they are guaranteed to come apart. I don't know how long it'll take, but the more heat and wet/dry cycles they experience the sooner they will come apart.

    I'm talking about pieces of wood brought together into a structure.
    Epoxy IS definitely more versatile. You can glue wood together and seal it with the same epoxy. You can fill gaps and fillet, you can laminate fiberglass onto wood and foam panels with the same stuff. You could probably do a barrier coat on the hull with it. But, by definition, you only achieve a mechanical bond.
    I hesitate to use that term here as the adhesion is mechanical but not a BOND. There is no comparing here with Resorcinol which can only glue flat pieces of wood together FOREVER. It has a bad rap because of its short open time and need for high clamping and controlled temp.

    If I had been more comfortable with Resorcinol I might have done A-338's strongback lamination with it. I felt I couldn't do it within the short open time required.

    It is entirely possible to put together a new rudder for the Ariel/Commander with foam and glass OR plywood and glass using good epoxy. There is always the chance that the epoxy can separate from the wood or the foam.
    You have to take this into account when designing the rudder. But this is not gluing wood-to-wood. The whole intent is to encapsulate the wood - and it sometimes doesn't work. Exposed, varnished wood swells and shrinks. Epoxy glue-line is more or less non-shrink and hard. Wood wins.

    If you had to glue wood-to-wood together for underwater use (like the original non-encapsulated rudder) Nobody would spec epoxy. It's possible to butcher-block and pre-bond pieces together into 'planks' with Resorcinol for cutting the shape and use polyurethane or polyether for gluing/caulking edge to edge planks. Most people these days would then SEAL the wood with a thinned epoxy, then attempt to waterproof with a polyurethane coating (or whatever new comes down the everchanging chemical pike.) Or go right to bottom paint. Imco that's conventional wisdom.

    In every case epoxy must be protected with another coating. Even a novolac needs UV protection. Pigmented epoxy coatings/paints will chalk and breakdown. There is no comparison with LPU coatings Even polyester coatings will outlast epoxy coatings. On those winch islands use a clear coating with the highest UV rating you can find. That'll help some.

    The chemistry keeps changing. There are new combinations appearing: epoxy polyesters. epoxy urethanes and resorcinol epoxies, and ETC for both adhesives and coatings. Quite amazing.
    But at the moment everyday epoxies that we buy really have limited use on the exterior of a cruising sailboat.

    Please, I work with these assumptions on my Areil. If there are developments or stuff I've forgotten (more likely every day), please clue me and the boat in! We both depend on it.
    The limited info about glues and coatings that I work with IS ALL conventional.
    __________________________________________________ _____________________________________________
    google>
    Laminating white oak w/ Resorcinol - The WoodenBoat Forum
    __________________________________________________ _____________________________________________
    For unstressed gluing somebody by now must have tried using CLEAR polyether or a silyl-urethane. !NOT SILICONE! Also sold as Hybrid Sealant/adhesive.
    This is a one-part, low odor, 100% solids, long life, moisture cured, always flexible synthetic rubber in a gun tube.
    Worth experimenting - like gluing a stack of mahogany blocks together and boiling them for awhile!!!
    Last edited by ebb; 01-29-2010 at 08:10 AM.

Similar Threads

  1. All those wires inside my mast gotta go!
    By Scott Galloway in forum Technical
    Replies: 26
    Last Post: 07-04-2007, 07:40 AM
  2. Commander- replace mast support with cross beam
    By beugenides in forum Technical
    Replies: 2
    Last Post: 01-11-2005, 12:04 PM
  3. Tabernacle Operation
    By Scott Galloway in forum Technical
    Replies: 17
    Last Post: 09-04-2003, 08:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts